I have various types of temp probes, with appropriate couplers, that hookup to a digital meter (Fluke). I need to know the recommended location/depth I should put these. The furnaces are Lyman Mag 20 and a Saeco. I have learned that I need to keep a closer eye on the alloy temp.
Temperature probe depth and location
- 6.1K Views
- Last Post 02 December 2012
I have various types of temp probes, with appropriate couplers, that hookup to a digital meter (Fluke). I need to know the recommended location/depth I should put these. The furnaces are Lyman Mag 20 and a Saeco. I have learned that I need to keep a closer eye on the alloy temp.
I use a PID controller with a high temp probe & I keep the probe just a little off from the bottom of the pot. 1/4” to 1/2". You may want to consider building your own PID temperature control. I built mine for about $50.00. Fluke meters are pretty expensive . . . wouldn't want to damage one. I have two Fluke meters at a cost of over $200.00 each and they are the cheaper ones. Build a PID. You'll be happy.
If someone else had of done to me what I did to myself . . . I'd have killed him. Humility is an asset. Heh - heh.
Attached Files
Tanks for the reply. I got the flukes from where I used to work, they upgraded to a newer model. Anyway, do you have plans for a PID?
Attached Files
Pigslayer has his about where I have mine, 1/2 inch from bottom and and 1/2 from side. Error on having more space, as that tends to be more stable. Ric
Attached Files
Tanks for the reply. I got the flukes from where I used to work, they upgraded to a newer model. Anyway, do you have plans for a PID?
Somewhere on this site the building of a PID has been discussed with a diagram. If you need help with parts, I'll locate the sources for you. I think that Jeff submitted a diagram. Let me work on it.
If someone else had of done to me what I did to myself . . . I'd have killed him. Humility is an asset. Heh - heh.
Attached Files
Pat,
A write up of your design for a PID controller and high temperature probe would make a great Fouling Shot article. I'm sure there would be interest by members. Your posts and pictures you have prepared for the forum would be a good start. The goal might be to give readers enough information to build one themselves.
Think about it.
John
Attached Files
I second that suggestion !!
Pat,
A write up of your design for a PID controller and high temperature probe would make a great Fouling Shot article. I'm sure there would be interest by members. Your posts and pictures you have prepared for the forum would be a good start. The goal might be to give readers enough information to build one themselves.
Think about it.
John
mrbill2
Attached Files
Do you have a schematic/parts list for your PID? Please send it to me. Thanks Ron
Attached Files
I am new to this. What/where is “Fouling Shot"?
Attached Files
"The Fouling Shot” is the members magazine of the Cast Bullet Association. Join, and you receive 6 issue per year.
Attached Files
I sent all the information you guys are talking about to the Fouling Shot about 3 or 4 years ago and that is where it died. I figured that since I build and sell these units that they did not want to give me free advertising. I am cheap when I buy parts and if you can find everything for $50 to build one we would all like to know that secret. Please pass it on.
Attached Files
Pat,
A write up of your design for a PID controller and high temperature probe would make a great Fouling Shot article. I'm sure there would be interest by members. Your posts and pictures you have prepared for the forum would be a good start. The goal might be to give readers enough information to build one themselves.
Think about it.
John
John, Push this one if you could. Would make a great article. :fire
Attached Files
O.K. Give me a little time fellas & I'll draw up a diagram & post it along with a bill of materials. I'm “on call” this week so won't have much time for a few days. Be patient. Pat
If someone else had of done to me what I did to myself . . . I'd have killed him. Humility is an asset. Heh - heh.
Attached Files
Not to be a contrary but theory aside has a test been done to see if a perfectly temp controlled pot gives better bullets and smaller groups? It would be an interesting test.
"if it was easy we'd let women do it" don't tell my wife I said that!
Attached Files
Not to be a contrary but theory aside has a test been done to see if a perfectly temp controlled pot gives better bullets and smaller groups? It would be an interesting test.
I've shot frosted bullets and shiney crisp, sharp edged bullets & though I'm not a cast bullet match shooter, I've never really noticed any difference as far as accuracy as long as the bullet has good fillout. But it does seemed to me that the nice shiney, well formed bullets would have better expansion on game than a frosted seemingly crystalized alloy. When I first read about a PID cotroller several years ago I was skeptical as to the need of one and scoffed at those who used one. (The Old Dog & New Tricks syndrome. LOL) But then I got curious & built one . . . never looked back, I love it!
Pat
If someone else had of done to me what I did to myself . . . I'd have killed him. Humility is an asset. Heh - heh.
Attached Files
The controller setup is shown is in an electric pot but could you also use it in a open pot and ladle setup ?
Attached Files
The controller setup is shown is in an electric pot but could you also use it in a open pot and ladle setup ?
You mean like over a open flame burner? In that case it wouldn't do much good.
If someone else had of done to me what I did to myself . . . I'd have killed him. Humility is an asset. Heh - heh.
Attached Files
This is a basic/generic diagram. The pinouts for your thermocouple may vary with your PID. Also please note that a “High Temp. Probe only has two wires. No, you don't need an alarm as it would probably drive you nuts until you got up to temp.! On mine a put a bypass so I could switch from PID control to pot control. All the parts came from ebay for under $50.00. The box I made from some galvanized sheet metal that I had left over from installing my furnace.
If someone else had of done to me what I did to myself . . . I'd have killed him. Humility is an asset. Heh - heh.
Attached Files
Just a thought for the open pot guys. Put probe in pot, set pot on single burner hot plate, let controller control hot plate. What is the difference between that element and the element in the electric pot? Trust me, the probe is real dumb, it only knows the temperature not the source of the heat. Got a 240v hot plate? No problem. Just interupt one leg. Your stove in the kitchen has worked that way since forever. Or buy two SSRs and wire the control side in parallel.
And when you buy your SSR make sure it is rated properly. The above diagram ASSUMES you have a line voltage primary on the SSR. Just so you don't let the magic smoke out when using the above scheme: SSR primary voltage 240 volt AC or higher, control voltage 3-32 volt DC and SSR rating of 25 amps or greater. Now I am ASSUMING the control voltage because I can not read the output on the controller. This control scheme is one of many that will work.
There must be a thousand answers to the same question. As I used to tell my apprentices, this is how I would do it. Now go figure it out for yourself so you learn something.
Attached Files
Just a thought for the open pot guys. Put probe in pot, set pot on single burner hot plate, let controller control hot plate. What is the difference between that element and the element in the electric pot? Trust me, the probe is real dumb, it only knows the temperature not the source of the heat. Got a 240v hot plate? No problem. Just interupt one leg. Your stove in the kitchen has worked that way since forever. Or buy two SSRs and wire the control side in parallel.
And when you buy your SSR make sure it is rated properly. The above diagram ASSUMES you have a line voltage primary on the SSR. Just so you don't let the magic smoke out when using the above scheme: SSR primary voltage 240 volt AC or higher, control voltage 3-32 volt DC and SSR rating of 25 amps or greater. Now I am ASSUMING the control voltage because I can not read the output on the controller. This control scheme is one of many that will work.
There must be a thousand answers to the same question. As I used to tell my apprentices, this is how I would do it. Now go figure it out for yourself so you learn something. Thanks for your post. Yes, there are a number of control schemes and as I said, the above one is Generic if you will. It will be up to the builder to have some electrical knowledge. What is simple to guys like you & I can be a major challenge to others. A word of caution to those who may be electrically challenged. You may be wise to have someone build one for you. It'll be worth the money.
If someone else had of done to me what I did to myself . . . I'd have killed him. Humility is an asset. Heh - heh.
Attached Files
George wrote: "Not to be a contrary but theory aside has a test been done to see if a perfectly temp controlled pot gives better bullets and smaller groups? It would be an interesting test."
George, Don't give contrary a bad name. Excellent question. If I were betting I would bet that it doesn't. I would like to have closer control anyway. Like weighing bullets the main purpose may be just to raise confidence. It also looks impressive on Pat's bench.
John
Attached Files
Categories
- All Categories
- General Polls
- Contact Us w/ Forum Issues
- Welcome to The Cast Bullet Association Forum
- General
- Bullet Casting
-
Guns and Shooting
- AR Platform
- TC Contenders & Other Single Shot Handguns
- Shotguns
- Informal Matches & Other Shooting Events
- Gunsmithing Tips
- Gun Cleaning & Maintenance
- Optics
- Benchrest Cast Bullet Shooting
- Military Bench Rest Cast Bullet Shooting
- Silhouette Shooting
- Postal Match Cast Bullet Shooting
- Factory Guns
- Black Powder Cartridge
- Hand Guns
- Lever Guns
- Single Shot Rifles
- Bolt Action Rifles
- Military Surplus Rifles
- Plinkers Hollow
- Muzzleloaders
- Hunting
- Reloading
- Buy, Sell or Trade
- Other Information & Reference
Search
This Weeks High Earners
- Aaron 28
- jeff houck 20
- Tom Acheson 18
- Wilderness 14
- John Carlson 13
- sghart3578 10
- MarkinEllensburg 10
- Spindrift 5
- alphabrass 5
- SkinnerD 5