mica substitute

  • 15K Views
  • Last Post 11 September 2019
drsquat posted this 15 March 2007

what does anyone think about using  talcum powder applied to lube bullets to make them easier to handle?

Attached Files

Order By: Standard | Newest | Votes
Ed Harris posted this 21 March 2007

Calcium stearate comes in flake-granular form, but this breaks down readily if applied in a drum tumbler. A Chock Full-O-Nut coffee scoop full will coat 5000 bullets. Best method to apply is to place 5000 bullets in a 5-gallon bucket and mechanically agitate for one minute. Some commercial casters use a paint shaker for this, but violent agitation will peen the surface of soft cast bullets. I prefer to roll the container while on its side, holding the bucket by the wire bail.

73 de KE4SKY In Home Mix We Trust From the Home of Ed's Red in "Almost Heaven" West Virginia

Attached Files

  • Liked by
  • M3 Mitch
Geo. posted this 24 March 2007

What you guys (excepting Ed) do not realize is that the suggestion to use Calcium Stearate is an astute one.

Calcium Stearate is the calcium soap of stearic acid. If you dissolved sodium stearate, as in normal soap, in hard water you would get a certain percentage of calcium stearate as hard-water scum.

Back in the days of yore when Col. Harrison and crew did the NRAs seminal work on cast bullets, they noted that waterpump grease made good bullet lube. Waterpump greases were often based in a calcium soap formula.

Alox is a calcium based soap that was originally meant for the auto industry (and others) as a protective coating. I would be more correct to state that the family of Alox protectives contains compounds made of calcium-based soaps.

So--give it a try because the chemistry is correct and advantageous.

Attached Files

  • Liked by
  • M3 Mitch
Ed Harris posted this 26 March 2007

Geo. wrote: What you guys (excepting Ed) do not realize is that the suggestion to use Calcium Stearate is an astute one.

Calcium Stearate is the calcium soap of stearic acid. If you dissolved sodium stearate, as in normal soap, in hard water you would get a certain percentage of calcium stearate as hard-water scum.

Back in the days of yore when Col. Harrison and crew did the NRAs seminal work on cast bullets, they noted that waterpump grease made good bullet lube. Waterpump greases were often based in a calcium soap formula.

Alox is a calcium based soap that was originally meant for the auto industry (and others) as a protective coating. I would be more correct to state that the family of Alox protectives contains compounds made of calcium-based soaps.

So--give it a try because the chemistry is correct and advantageous.

Yup!  -  all correct.

I wasn't going to bore everyone with the details, just know that it works and you can buy it in at the drug store.  

8-)

73 de KE4SKY In Home Mix We Trust From the Home of Ed's Red in "Almost Heaven" West Virginia

Attached Files

  • Liked by
  • M3 Mitch
CB posted this 29 March 2007

The question asked was:

what does anyone think about using  talcum powder applied to lube bullets to make them easier to handle?  (drsquat)

The point isn't which is less abrasive, because I also made a point that the lead bullet and copper jacket is a harder material. I worked around ground mica and Zinc stearate every day at work for 16 years. The applications for coatings were used for completely different processes and the mica was a far superior coating when applied to a tacky material.

How bad is ground mica? There is absolutely no 'haz mat' warning for it! We did not use or wear any protective mask or clothing, at the manufacturer's recommendation and OSHA's guidance. I would leave work shining with a coating of mica all over me and just as much in my lungs. Mica was everywhere in the air and on the steel machinery, which I never noticed wear away from abrasion.............Dan

Attached Files

  • Liked by
  • TRKakaCatWhisperer
CB posted this 29 March 2007

Here is something to think about...

Motor Mica is sold and used by many a reloader to lubricate the inside of the necks of their cases prior to resizing. I am sure that some remains in the case when they load it. I don't know if any survives after the powder burn to make it's way down the barrel.

Zinc Stearate is mainly used as a release agent for powdered metal applications. The problem with this is when it is burned it releases zinc oxide fumes, which are quite hazardous. Zinc Stearate has a melting temp of about 140 degrees , I would be curious to find out if mica has a melting temp.

There is an alternative to Zinc Stearate called Acrawax, used for the same purpose, same results, but no toxic fumes.

Lithium Stearate and Calcium Stearate are used to make greases. They are the thickening agents. Most bullet lubes use a type of grease as the base ingredient, such is the case with Alox, which is basically a very thick grease. Lithium Stearate is hard to get a hold of, Calcium Stearate may be a little easier. I have been advised that many of the compounds in the stearate family have been classified now as, of all things, flammable, making it a hazmat compound.

Mica is rock Talc is rock Calcium is mineral Lithium is metal Zinc is metal Which is worse? Who knows...

Attached Files

  • Liked by
  • M3 Mitch
David Reiss posted this 10 September 2019

I agree with Larry, no heat is necessary for this lube. However I do understand the comment about being messy. Here in Texas it can be "quite tacky" and storing the bullets in bulk is not an option. This is what got me to start storing the lubed bullets in the Styrofoam ammo trays. It keeps the bullets from sticking to one another and pulling lube from one to the other. Handling is much easier when using this method of storage. 

David Reiss - NRA Life Member & PSC Range Member Retired Police Firearms Instructor/Armorer
-Services: Wars Fought, Uprisings Quelled, Bars Emptied, Revolutions Started, Tigers Tamed, Assassinations Plotted, Women Seduced, Governments Run, Gun Appraisals, Lost Treasure Found.
- Also deal in: Land, Banjos, Nails, Firearms, Manure, Fly Swatters, Used Cars, Whisky, Racing Forms, Rare Antiquities, Lead, Used Keyboard Keys, Good Dogs, Pith Helmets & Zulu Headdresses. .

Attached Files

  • Liked by
  • M3 Mitch
Larry Gibson posted this 11 September 2019

Perhaps but I've been using GC'd bullets for that for years.....313631 or 311316 in the 32 H&R Magnum, 358156 in the 357 Magnum, 410610 in 41 Magnums, 429415, 429244 and 429640HP in 44 Magnums and 452490 in the 45 Colt.  Cast of 40, 30, 20 or 16-1 alloy those bullets can be pushed with excellent accuracy to as fast as the cartridge/firearm will safely allow. 

LMG

Concealment is not cover.........

Attached Files

  • Liked by
  • TRKakaCatWhisperer
Ed Harris posted this 16 March 2007

Talc is abrasive and will make a REAL mess in the bore. If you want to make the lube non-tacky you could use calcium stearate instead of motor mica.

73 de KE4SKY In Home Mix We Trust From the Home of Ed's Red in "Almost Heaven" West Virginia

Attached Files

TRKakaCatWhisperer posted this 19 March 2007

So is there an issue with mica?

 

 

Attached Files

CB posted this 19 March 2007

Mica is abrasive, it would be like shooting a ton of lapping bullets down your bore.

I take it drsquat that you are looking for a way to keep the lube from sticking to your hands correct?

What kind of lube are you using?

Attached Files

drsquat posted this 20 March 2007

Yes, just looking for a way to cut down on the mess. The lube i am using is Lyman Alox. With a Lyman 450 and a soldering iron attached for heat lol thanks Drsquat

Attached Files

CB posted this 20 March 2007

If I were you I would consider changing lube. Alox is sticky regarless of what you do to it.

I would try Something else, I take it you are planning to shoot mainly pistol?

Without giving a plug for someones products, I think if you were to puruse the forum I think you would find something that would work better for you.

Attached Files

Maven posted this 24 March 2007

I don't thin calcium stearate is available in non-commercial quantities in my area, but would corn starch be a suitable alternative?

Attached Files

CB posted this 24 March 2007

Well I can tell you it aint cheap! I bet about $50 for 1 LB..

http://www.sciencelab.com

Attached Files

TRKakaCatWhisperer posted this 25 March 2007

I did find it difficult to believe that mica (which FEELS so slick) could be abrasive - until I looked it up!

I wonder if it would be any good for lapping - it does have abrasive qualities, but is MUCH finer than the grade of abrasives used for fire-lapping (closer to toothpaste, and IS found in some brightening toothpastes).

I'll bet the calcium stearate is available for much less - perhaps not at the same grade or quality but at a quality that is perfectly adequate for launching bullets.

It is used in Felix's lube and there are quite a number of folks that make their own bullet lube using it.

 

Attached Files

Shuz posted this 25 March 2007

TRK--Where did you see that mica was abrasive? I've been using Midway Mica for years to keep the NRA 50/50 and other soft lubes from being soo messy. Now just because I'm using it, doesn't make it right,but how come so many have advocated using it for the same purpose I do? Inquiring minds wanna know? Where can I “look it up"?--thanks,Shuz

Attached Files

CB posted this 25 March 2007

Mica powder and Talcum powder are made from a same class of mineral from the silicate family. Mica is made from Muscovite with a hardness of 2-2.5. Talcum powder is made from a form of Magnesium Hydroxide with a hardness of 1! Pure lead had a hardness of 1.5 and copper (copper gascheck) a hardness of 2.5-3! Let alone the consideration of antimony and tin.

Somebody needs to get a life! When it comes to stuffing abrasive material down yer bore, the projectile itself dose a lot more damage than these powders, or lint, or coated cleaning rods. The residual carbon fowling being ground down the bore shot after shot more than likely has the most wear affect on the bore. Mica and talcum powder is about the softness material you can stick down yer bore.

Hey drsquat, I'd go ahead and use Talcum powder and find one with a goooood smell added to it for more pleasant shooting sessions, unless someone objects to the added smell is too abrasive :)....................Dan

Attached Files

drsquat posted this 25 March 2007

lol thanks Dan, I believe I will

Attached Files

Shuz posted this 26 March 2007

Thanks, Dan, for putting the abrasiveness in perspective. I'm prolly a lot more abrasive at times than Mica! I'll continue to use it because it sure makes the cast bullets a lot easier to handle.

Attached Files

CB posted this 26 March 2007

Shuz,

Ya, I'm an old rock hounder and my son is a geologist. The Mohs scale hardness is just a relative test for identifying rock specimens, so it isn't absolute. Talc is the softest rock out there, so none of this was making sense to me. Talc is ground pretty fine for talcum powder and if it was abrasive, they sure wouldn't put it on baby's butts!..............Dan

Oh drsquat, that reminds me. We used to use scorched corn starch on our baby's butt and it worked better than talcum powder. Maybe corn starch would werk fer yer bullets?

Attached Files

Show More Posts
Close