I just got back from a WW hunt --scored 2 1/2 5 gal pails mixed WWs (300+lbs) What is the best procedure to separate the lead wgts from the non lead. ??? I have a bottom drop Lee furnace and a Propane-and iron pot set up // JP
Processing Wheel Weights
- 1.7K Views
- Last Post 29 January 2016
After separating zinc from lead. Keep the melting pot temp lower that the melting point of zinc. Drop in a few at a time, stir and watch zinc float to top then scoop away. Some say zinc looks like oatmeal floating on top of melt, but so does good alloy when not fluxed.
I bet there is a lot of zink mixed in with modern WW because of recycling.
...
Attached Files
Keep WW rendering temp below 625 degrees F.beltfed/arnie
Attached Files
Where can I get a 1000 deg thermometer ??? JP
Attached Files
Thermometers are available from NOE, Lyman (mine does not work), RCBS, and Amazon . Com. I think that amazon.com is the least expensive. These are all dial thermometers, and will exhibit varying accuracy. You can also get laser remote reading thermometers, but you will need to float a can lid or something similar on the melt to get a decent temp read. Those are available fro Harbor Freight and a whole lot of other places. Brodie
B.E.Brickey
Attached Files
I fired up the Propane cooker and melted down the 47 lb bucket of WW I brought home--fluxed with sawdust-- heated it all and scooped off all that didn't melt--ended up with 36 lbs of corn tin ingots-- now to test hardness //JP
Attached Files
I did the Ball bearing test on the WW and got BN 9.76// does that sound reasonable ?? JP
Attached Files
Did you melt stick-on and clip-on weights together or just clip-on? I usually get closer to 12BH for clip-on. If you mixed the two types together your number could be correct.
Attached Files
I put it all togather--was surprised to get as much good stuff as I did// I.ll pick up the other 2 pails tomorrow// JP
Attached Files
I always try to keep stick on separated from clip on so that I ahem near pure lead avail from one and 11-13 BHN alloy on the other. Then I can blend, shoot soft BP loads, etc. Offers some flexibility. May not bee needed for you.
Attached Files
I started picking and sorting the stuff but a 5 gal bucket (130Lbs ) has about 5000 pcs and it would take forever//
I also found that some of the stick ons don't melt out also// 100 lbs of WW will make 7000+ 93 gr bullets which will last my lifetime// I also have about 100+ lbs pure lead if I need it JP
The interesting fact is : when I finally get the pistol I could buy 500 rounds factory and be Way ahead of this project /// (not so much fun thu//
Attached Files
If you are testing for hardness right after they cool down you will get an inaccurate reading. They need time to fully harden. I usually wait 3 weeks.
Robert Homan
Attached Files
I re tested the WW stuff 3 days later and it at about 15 deg f-- tested 14.7 ish from first test @ 9+- makes one wonder?? JP
Attached Files
I did the Ball bearing test on the WW and got BN 9.76// does that sound reasonable ?? JP
That's what I get. I sort all the Zn and Fe WWs and discard them. Also remove the stick on that is usually about 6 BHN.
Traditionally clip on WW is stated as 12 BHN but in 25 years of casting I have never registered it more than 9.5-10 BHN.
Incidentally, if you add a little tin to stick on WW (40-1) it will run around 8 BHN and I have heat treated it to 12 BHN. Makes for an awesome hunting alloy.
Cheers from New Zealand
Attached Files
Question: If I am casting at say BHN 12 and I drop the bullets into water// what kind of hardness can I expect or 9.7 to?? 14.0 to?? JP
Attached Files
Question: If I am casting at say BHN 12 and I drop the bullets into water// what kind of hardness can I expect
or 9.7 to??
14.0 to?? JP
Closer to 18 for water dropped after the bullets have aged a few weeks.
Attached Files
Categories
- All Categories
- General Polls
- Contact Us w/ Forum Issues
- Welcome to The Cast Bullet Association Forum
- General
- Bullet Casting
-
Guns and Shooting
- AR Platform
- TC Contenders & Other Single Shot Handguns
- Shotguns
- Informal Matches & Other Shooting Events
- Gunsmithing Tips
- Gun Cleaning & Maintenance
- Optics
- Benchrest Cast Bullet Shooting
- Military Bench Rest Cast Bullet Shooting
- Silhouette Shooting
- Postal Match Cast Bullet Shooting
- Factory Guns
- Black Powder Cartridge
- Hand Guns
- Lever Guns
- Single Shot Rifles
- Bolt Action Rifles
- Military Surplus Rifles
- Plinkers Hollow
- Muzzleloaders
- Hunting
- Reloading
- Buy, Sell or Trade
- Other Information & Reference
Search
This Weeks High Earners
- Aaron 25
- jeff houck 20
- Tom Acheson 17
- Wilderness 14
- John Carlson 13
- sghart3578 10
- MarkinEllensburg 10
- Spindrift 5
- alphabrass 5
- SkinnerD 5