Friends: I would like some advice and your preference as to casting ladles. I own a Lyman and am aware of the Rowell products. Seems even the small Rowell#1 holds a pound of lead. I know, you don't have to fill it but it still seems a little large. My Lyman, well it just feels kind of clumsy (or it could be me) as I'm used to the bottom pour method. So, if any of you have a link to or a picture of your favorite I would appreciate your input. Thanks GP
casting ladles
- 3K Views
- Last Post 26 June 2015
I prefer my 50yr old Lyman ladle with the shorter handle. Grouch
Attached Files
There is some logic to selecting a casting ladle size. You likely may have single and double through 6 cavity molds. If you select a ladle that will hold 2 to 4 times the amount of metal for your mold that needs the most metal to fill all cavities, you will then have a ladle that is large enough for your needs. A smaller ladle than that cools too quickly to be thermodynamically efficient for your ladle casting application with just one ladle. The Rowell 1 pounder is a good selection for big bullet 6 cavity mold pouring.
Gary
Attached Files
For use with a Paul Jones 415-grain single cavity mould, the old RCBS works well. But for most other multi-cavity moulds the Rowell ladle works very well. The Magma engineering 40-pound pot has an ID of 5” which helps for ladle use. The Lyman ID is 4 1/2". The old Lee 5-pounder is used to melt down wheel weights off to the side while doing regular bullet casting.
Tom
Attached Files
Geez, I thought everybody did what I do- ladle the lead into the mold in a lovingly fashion via a Tiffany silver spoon. :)
Attached Files
I am still using the Lyman ladle I started casting with, 50 some years ago. Used it for many years casting pistol bullets in a 4 cavity H&G mold. Now use it almost entirely for rifle, mostly .30 cal. but some .375 cal. but nothing over 2 cavity molds.
If you're going to cast with a 4 or six cavity large caliber mold, a Rowell ladle may make things a little easier, but otherwise a Lyman or RCBS regular ladle works just fine. I have an idea any ladle feels and works right after you use it enough to get used to it. One thing: even a Lyman or RCBS ladle holds too much lead for most 2 cavity molds. It helps to learn how full your ladle needs to be when casting with a one or two cavity mold.
Wes
Attached Files
Thanks for the replys guys, I believe it's like Wes said, just a matter of getting use to the tools at hand. I got out my Lyman ladle, RCBS cast iron bowl and the Camp Chief one burner propane stove today and gave ladle casting a chance. Happy to say all worked very well for me. I've always just used my bottom pour Mag 20 up until now. As posted on another thread, I was having problems with spout freeze with an alloy containing babbit. This pushed me to the ladle and I'm glad for the nudge. Thanks Guys GP
Attached Files
I like the RCBS. It has a square back side. This makes it easier for me to dmp any dross off of the ladle.
Attached Files
For about 35 years I have been using a home-made ladle made from a soda syphon gas cylinder. I cut off half the top and brazed on a handle made from the twisted wire of an industrial brush. Eight inches long makes a good balance as it sits nicely in the small Lee pot that I ladle cast with. Bore a hole in the spout after having a look at the size of your sprue hole and you are good to go. Also an easy way for a lefty to have a ladle that suits. Bullets up to 450 grains are no trouble, but could not keep a large six cavity mould hot.
Attached Files
Re: ladle pouring for southpaws; I believe RCBS ladles have been made for either hand use for some time now. (You can screw the handle into the ladle from either side.)
I think Lyman ladles are now made the same way, too.
Wes
Attached Files
I use one I made out of a small food can,about 2” wide and 2.5” deep.twisted fence wire for the handle,bent the side in a trifle to form a pouring lip.No need to fill it all the way to the top,4 and 6 cavity are easy. Mike.
Attached Files
I would never NOT use a bottom pour. If I had to use a ladle, I would first use the Lyman, just because I have never read any one having a complaint about it. Obviously, a lefty may need something made for them.
Attached Files
Years ago, when I began casting, I used the Lyman ladle. It was so handy, what with not having to let go of the mould, to tap the sprue plate, etc. and just seemed so natural, that I doubt if I could even use a ladle left-handed, (even though I do everything else as a lefty.) It would take a lot of re-training. But, after many years of using a bottom-feed pot, and force-feeding my moulds, the thought doesn't even occur to me now. I'm spoiled, I guess.
Bill
In theory, there's no difference between theory and practice. In practice, there is. My fate is not entirely in Gods hands, if I have a weapon in mine.
Attached Files
Categories
- All Categories
- General Polls
- Contact Us w/ Forum Issues
- Welcome to The Cast Bullet Association Forum
- General
- Bullet Casting
-
Guns and Shooting
- AR Platform
- TC Contenders & Other Single Shot Handguns
- Shotguns
- Informal Matches & Other Shooting Events
- Gunsmithing Tips
- Gun Cleaning & Maintenance
- Optics
- Benchrest Cast Bullet Shooting
- Military Bench Rest Cast Bullet Shooting
- Silhouette Shooting
- Postal Match Cast Bullet Shooting
- Factory Guns
- Black Powder Cartridge
- Hand Guns
- Lever Guns
- Single Shot Rifles
- Bolt Action Rifles
- Military Surplus Rifles
- Plinkers Hollow
- Muzzleloaders
- Hunting
- Reloading
- Buy, Sell or Trade
- Other Information & Reference
Search
This Weeks High Earners
- John Carlson 23
- Bud Hyett 21
- linoww 17
- MP1886 13
- MarkinEllensburg 10
- drone 9
- Wilderness 8
- Aaron 7
- beltfed 6
- Lucky1 6