I have always lubed my cast bullets with rcbs bullet lube. I have never used alox. My question is do you use both or just alox by itself
Lee Liquid Alox
- 3.2K Views
- Last Post 02 December 2020
does anyone have an answer? If alox is a good lube it seems redundant to use both alox and rcbs bullet lube on the same cast
Attached Files
Does your RCBS bullet lube contain alox ?
Long time Caster/Reloader, Getting back into it after almost 10yrs. Life Member NRA 40+yrs, Life S.A.S.S. #375. Does this mean a description of me as a fumble-fingered knuckle-draggin' baboon. I also drool in my sleep. I firmly believe that true happiness is a warm gun. Did I mention how much I HATE auto-correct on this blasted tablet.
Attached Files
does anyone have an answer? If alox is a good lube it seems redundant to use both alox and rcbs bullet lube on the same cast
Hi. I don't quite understand your question. Are you talking about tumble lubing after you've applied RCBS lube in a lube-sizer? If so, you certainly can, and it won't hurt, but I feel is probably unnecessary. If you've never tried tumble lubing, it's easy and effective. Here's an excellent thread on tumble lubing on the other cast site. You can make your own 45-45-10, or buy it ready made from White Label Lube. ETA: "xlox" is the same stuff as "Alox," but the name is trademarked, so Lars had to use another name. Hope this helps.
Ed
Growing old is mandatory, growing up, however, is totally optional!
Attached Files
One or the other. Ben's mix is best for tumble lube followed by a tumble in dry powder lube to avoid stickyness.
Attached Files
We have had tests reported both on this forum and in the Fouling Shot that show that many, probably most, cast bullet loads may not need what we call lubricant at all -- as in none.
I suppose some people are suggesting conventional lube plus tumble lube, but I have seen NO testing results that give the slightest hint that this does any good or even results that it doesn't hurt accuracy. We have been getting good results with only in the groove type "lubes" for 150 years why add tumble lube now.
If you do decide to use both, please run tests with and without and find out if it improves or degrades accuracy. Results would make a good post for this thread. Facts instead of opinions are always welcome but usually scarce.
John
Attached Files
The NRA ALOX/Beeswax formula is an attempt to make ALOX easy to use for lubricant. Beeswax is a carrier to allow the ALOX to be applied, beeswax stiffens the ALOX to where is can be easily and reliably applied in a lubrisizer. The Javelina Schuetzen lube is 75% beeswax with 25% ALOX to have a softer lube for this specialty application. In terms of effectiveness and time to apply, both the NRA formula and Liquid ALOX end up with the same overall expenditure of time.
Experimented with lubricants in the 6mm bore, I was searching for something in the 2300/2400 fps range to be competitive for wind drift at 200 yards. I found some work better than others, the NRA formula quit for accuracy above 2000 fps. Nice round groups without leading, but greater in size. I seem to have a kiss of death for lubricants, every time I attempt to standardize on a lubricant, it goes off the market; M&N, Gray's 24, Jake's Lube, all have disappeared when I go back to order a larger amount, a two or three year supply.
Farm boy from Illinois, living in the magical Pacific Northwest
Attached Files
what is "dry powder lube" ??
Molybdenum DISULFIDE
Attached Files
I use Lee Liquid Alox cut 50/50 with mineral spirits and dust with motor mica when dry to eliminate stickiness. This on regular ( not tumblelube ) bullets.. I keep velocity reasonable and don't have problems.
beagle6
Attached Files
From CPA Rifles: Javelina Schuetzen lube, consisting of a 75/25 mix of Alox 350 and beeswax. Sold in 1 pound packages perfect for pan lubing.
Bud,
You're saying that Schuetzen lube is 75% Beeswax and 25% Alox. I mixed a batch at 75/25 Alox/beeswax (from the CPA website) and it's really gooey stuff. Maybe I got it backwards. What is the magic of Alox anyway?
Paul
Attached Files
I second the one or the other, not both comment. You can over lube and cause un-necessary fouling. Also I think that alox was developed as a sort of metal varnish, not sure on the magic part. Been around for a long time
Attached Files
Paul - You're saying that Schuetzen lube is 75% Beeswax and 25% Alox. I mixed a batch at 75/25 Alox/beeswax (from the CPA website) and it's really gooey stuff. Maybe I got it backwards. What is the magic of Alox anyway?
First, I got the ratios reversed, too much of a hurry to get outside and mow my lawn. (I've done this reversal trick before.)
Yes, it is gooey, and that is the what is needed. Like mixing oil and water, this is an emulsion more than a mixture and you almost have to beat them to get them together. That is why I buy the lube from Gail since I do not want to set up for this adventure.
ALOX is a brand name in several combinations. The number identifies the mixture and is proprietary. It was originally used as the liquid undercoat for car frames (Ziebart) for rust prevention. However someone decided to try this as a lube, I do not know why. The NRA Handloading Guide has an article on the "new" NRA Formula from the 1960's if you have that book.
I have been shooting SPG for both black powder and Schuetzen, but staying with SPG for black powder and going to Javelina for Schuetzen/Plain-base.
Farm boy from Illinois, living in the magical Pacific Northwest
Attached Files
On some of my more "aggressive" varmint loads;
The very last op after wiping cases off with acetone(finger nail polish remover) is to wipe the bore ride section with LLA. Trying to get it on very thin,then about the time say a box of 20 are done,buff it to a shine.
These are "jacked up" into JB velocity loadings. If I ran any less lube on the body.....it would be none. And the lube is about as low tech as it gets. 3-1 beeswax to vaseline. The reason for the LLA is because of a cpl things.
One is if there's been a nose bump op that creates a noticeable,albeit tiny slightly enlarged nose at the tangent area of the ogive. The other is when running a hard "jam". This is why it's only on some loads. In effect,it allows me to run a touch tighter nose on bore riders. The "test" is simply one you don't,or can't fail in the field.... a stuck bullet trying to eject a loaded round.
Attached Files
I use alox mix with lighter fluid for my 00 buck shot size down for to shoot in my 30 cal's it dry out well also
Attached Files
the Javalina Schuetzen Lube is 75% Alox350, and 25% Beeswax, if Alox 2138f is used ad 5% Microcrystiline wax, sticky and slippery, but works well for Breech Seating, too wet to use in a lubrisizer, I use it to pan lube
Alox 350 is different than Lee Liquid Alox,
Alox 2138f is different than either one, no longer available because of supposed carcinogenic features
Attached Files
I have used an RCBS LAM in the past but I have been using Lee Alox exclusively lately. I thin the Alox 50/50 with mineral spirits and add very little.
I mean 1/2 teaspoon per 100 bullets. They dry quickly. You can barely see any coating. I shoot up to 1900 fps with this.
And the Alox lasts a long time.
I see no need to use both.
Attached Files
I have been using Lee Liquid Alox for a lot of years and like it. The longer I use it the less I use. LLA is very tenacious and my experience is that it builds up in the bore during a shooting session. For a 38 special wadcutter load(around 700 fps) I use less than 1 drop of thinned LLA per bullet - thinned 50/50 with paint thinner.and think I could get away with less. Today I was experimenting with a 30 cal breech seated wildcat with 200 grain bullets lubed only on the driving bands with 50/50 LLA. Results were encouraging. I guess this could all be summed up as "Less Is More",
Attached Files
That is the beauty of the Ben's mix. Thin coating and when tumbled in dry lube 100% dry.
Attached Files
I use 45/45/10 warmed and applied sparingly to warmed bullets, about a 1/2 tsp to a hundred or so. I really like it. The tumble lube dries completely is not tacky and works even at higher velocities. Also, and this is very near and dear to my heart, it is CHEAP, and easy, and as they say "Less is more.".
B.E.Brickey
Attached Files
I made the KISS version of that lube. One can of JPW melted with a heat gun mixed with one bottle of LLA. So far it has worked well in 9mm bullets. I'm using the Lee 95 grain FP as cast with a starting charge of Unique. Very accurate and no leading. That one batch should last me a long time. Only difference between that and straight LLA is I have to slightly warm the bullets before coating. No problem if you have a heat gun.
Attached Files
I sell aprox 15K bullets/year.Not doing a business out of it but fulfilling some friends needs.Magnum handguns and 9mm bullets are lubed through my Star with the standard recipe 50/50 beeswax/alox recipe.
.38 spl wadcutter,45-70 and 30-30 rifle bullets get the liquid Alox(from LS Stuff)diluted at aprox 40/60(thinner/liquid alox).The rifle bullets are shot at aprox 1200/1400fps without gc and as far,nobody is coming back to me complaining that they lead the bore.When they come back,it is for reordering 500 more.I coat the bullets twice ;the first coating taking aprox 2-3 days to dry out,the second coating about half that time.Once a day,I simply put on a latex glove and roll them into the pan so that the alox gets evenly spread all around the bullets.Lubing 500 bullets takes but a few minutes...or many seconds depending on which you prefer.
After the solvent has dried away,the alox stays on the bullets quite sticky.Some of it will pack into the nose of the bullet seating punch,consequently driving the bullets deeper and deeper in the case.Not good!
To solve that problem.I simply put the bullets a few hundreds at a time in a small plastic container and spray them with talcum powder(am currently testing with corn starch so as to be more nature friendly and the tests so far do not show any difference).
The bores of the handguns and rifles are left shiny after shooting and as of now,I can say that I've shot over 500rds in my 45-70 without cleaning and so far the groups don't show any deterioration.To me(and my few customers)LLA and talcum works.
I've tried regular lube(50/50 alox beeswax in lube grooves) plus LLA and results haven't shown any improvement over one or the other;since I'm quite lazy,I've quit the experiment and went back home for a cold beer...or five!
Attached Files
I sell aprox 15K bullets/year.Not doing a business out of it but fulfilling some friends needs.Magnum handguns and 9mm bullets are lubed through my Star with the standard recipe 50/50 beeswax/alox recipe.
.38 spl wadcutter,45-70 and 30-30 rifle bullets get the liquid Alox(from LS Stuff)diluted at aprox 40/60(thinner/liquid alox).The rifle bullets are shot at aprox 1200/1400fps without gc and as far,nobody is coming back to me complaining that they lead the bore.When they come back,it is for reordering 500 more.I coat the bullets twice ;the first coating taking aprox 2-3 days to dry out,the second coating about half that time.Once a day,I simply put on a latex glove and roll them into the pan so that the alox gets evenly spread all around the bullets.Lubing 500 bullets takes but a few minutes...or many seconds depending on which you prefer.
After the solvent has dried away,the alox stays on the bullets quite sticky.Some of it will pack into the nose of the bullet seating punch,consequently driving the bullets deeper and deeper in the case.Not good!
To solve that problem.I simply put the bullets a few hundreds at a time in a small plastic container and spray them with talcum powder(am currently testing with corn starch so as to be more nature friendly and the tests so far do not show any difference).
The bores of the handguns and rifles are left shiny after shooting and as of now,I can say that I've shot over 500rds in my 45-70 without cleaning and so far the groups don't show any deterioration.To me(and my few customers)LLA and talcum works.
I've tried regular lube(50/50 alox beeswax in lube grooves) plus LLA and results haven't shown any improvement over one or the other;since I'm quite lazy,I've quit the experiment and went back home for a cold beer...or five!
i hate to admit this, but my Star luber/sizer and i, after 15 years or so, are about to part ways unless i can get the dam thing to start working. i use white label (?) lube and it takes so much heat and pressure to flow that it comes out the little hole at the bottom of the star tube and barely lube gets on the bullet grooves. i got some jakes alox, and its so soft it runs like melted butter everywhere. i go to bed at night with aching shoulders and back from fighting this thing. why now? i don't know. it sat dormant for a few years so i cleaned it up, put in new O rings. tried PC a few years ago. didn't like it. your method as described above sounds like a good alternative. would you PLEASE give me a step by step (as in showing a 3rd grader) set of instructions. yes its embarrassing that 4 months shy of age 70 and having been casting/reloading etc for 40 plus years i can't solve this. i'm going to PM you my email so no one will have to be bored if you'd rather do it that way. thanks
Attached Files
Categories
- All Categories
- General Polls
- Contact Us w/ Forum Issues
- Welcome to The Cast Bullet Association Forum
- General
- Bullet Casting
-
Guns and Shooting
- AR Platform
- TC Contenders & Other Single Shot Handguns
- Shotguns
- Informal Matches & Other Shooting Events
- Gunsmithing Tips
- Gun Cleaning & Maintenance
- Optics
- Benchrest Cast Bullet Shooting
- Military Bench Rest Cast Bullet Shooting
- Silhouette Shooting
- Postal Match Cast Bullet Shooting
- Factory Guns
- Black Powder Cartridge
- Hand Guns
- Lever Guns
- Single Shot Rifles
- Bolt Action Rifles
- Military Surplus Rifles
- Plinkers Hollow
- Muzzleloaders
- Hunting
- Reloading
- Buy, Sell or Trade
- Other Information & Reference
Search
This Weeks High Earners
- linoww 17
- pat i 17
- Millelacs 14
- trapdoor4570 13
- Idahocaster 12
- Aaron 11
- RicinYakima 10
- SkinnerD 9
- Glenn R. Latham 9
- Coydog 7