Included angle and throat-is this right?

  • 6.6K Views
  • Last Post 04 December 2007
CB posted this 14 August 2007

This is what I think is meant by included angle and throat. It desperately needs someone to draw a picture to go along with it.

Have I got this right?

Can you draw a picture?

Thanks;

joe brennan

Attached Files

Order By: Standard | Newest | Votes
Ken Campbell Iowa posted this 04 December 2007

I will only bring this up to be pondered .... no replies please until after xmas, otherwise Santy will not bring me any trick shooting equipment .....

uh..... I havent seen much discussion on this thread about that little space between the front of the case and the start of the ball seat ... usually ground out to about 45 per side stepdown from outside of case neck diameter to the start of the ball seat ... on your 308 W chamber, from say 0.340 down to 0.311 ... that little corner.. space ... silly little lead catcher ...

This is actually not understood too well, but at least in rimfire is important, because some guns don

... and for those of you who shoot the shorter 38 specials in 357 Mag chambers, because 38 brass is cheaper ... heh heh, you may have noticed a difference in accuracy.

If you think about it, when fired, the bullet metal probably is * obturated * to fill that little space and then is squoshed back down at the 45 degree shoulder to the diameter of the beggining of the free bore ....

This is not always a trivial thing, although we usually ignore it as just something to complicate our lives.

Remember, no discussion until next year ( 2008 ) ... just don

Oh yeah... there is such a thing as a chamber whose free bore is the same as groove diameter .... a competition match chamber for a heel bullet ... as in .. uh ... a .22 rimfire ( owch ) ... or my soon to be tested 20 gauge slug gun project.  Anyway, the chamber neck diameter is also the same ... or vice versa ...

regardez, ken campbell, deltawerkes

Attached Files

CB posted this 20 November 2007

Gee whiz Joe, I thought you had the terminology settled?  Pacific Tooling calls the ball-seat the 'lead' and the angled section the 'throat'. Clymer calls the ball-seat the 'free bore' and the angled section the 'throat'. Beats me?.................Dan

Attached Files

CB posted this 20 November 2007

Here's what we've got. Looking for a competent drawer!!!!!!!

NOTE: Montana Charlie's modification of my (lovely) drawing is included, but invisible, here at “CHAMBER", “FREE BORE", “LEADE” and “THROAT” since the drawing defines these terms.

            A drawing or picture would clear up many of the differences.

 

BALL SEAT

            The cylindrical section of the barrel cut just in front of the cartridge case

Ball Seat is the same as free bore.

 

BORE (DIAMETER)

            The as-made diameter of the bore of the barrel, in .30 caliber, nominally .300"

Now BORE is correctly used in only 2 instances. One is to describe the measurement from the top of one land, to the top of the opposite land, or another way, it's the minor diameter within the barrel created by the cutting of the grooves. The second way BORE may be used is when describing the ENTIRE interior surface of a barrel, as in, “The bore of my rifle shines.” This includes both the lands and the grooves.             Bore diameter - the diameter of the bore at the top of the rifling lands.

 

 

CHAMBER

           

 

FREE BORE

In a rifle chamber throat is also known as freebore and is supposed to be groove diameter with the rifling cut out.

 

Free Bore - the portion of the barrel from the end of the chamber to the beginning of the throat that is free from any rifling.

 

GROOVE (DIAMETER)

            The as-made diameter of the groove bottoms of the barrel, in .30 caliber, nominally .308"

The groove is exactly the dictionary definition . It is a narrow area where material has been removed from a surface and lies at a lower level. In saying, “My groove diameter is .308” describes the major internal diameter of the barrel, from groove to opposing groove. Or as an imaginary circle drawn perpendicular to the axis of the barrel and touching the bottom of each groove.

Groove diameter - the diameter of the bore at the bottom of the rifling lands.

 

GROOVE DEPTH

            The distance from the bore to the bottom of the groove, in .30 caliber, nominally .004".

 

LEADE (LEAD)

That section of the bore of a rifled gun barrel located immediately ahead of the chamber in which the rifling is conically removed to provide clearance for the seated bullet. Also called Throat or Ball Seat.

Another valuable term is LEADE. This is the area of rifling (lands) that begins at the end of the throat, and extends to the point where the lands attain their full height.

 

Leade - the area of the barrel from where the angle of the throat begins to where it reaches bore diameter.

 

THROAT

            The barrel from the end of the cartridge case to the place where bore and groove diameters are not cut.

            I believe “throat” describes everything ahead of the 'chamber' that is involved in transitioning from that chamber to the rifled bore

            In a rifle, the throat is the unrifled portion of the barrel between the chamber mouth and where the lands begin.

            On a revolter, throat is the part of the chambers at the front of the cylinder where the boolit rests (or should), )

in a rifle chamber throat is also known as freebore and is supposed to be groove diameter with the rifling cut out (lotsa throats in rifles are whatever size/shape they are).

Throat - the section of the barrel that begins at the point where the rifling starts

 

 

 

 

 

 

 

Attached Files

CB posted this 20 November 2007

Alight, this is my take on the definitions as I have been taught from the likes of Tom Gray and George Morrison...

Throat - the section of the barrel that begins at the point where the rifling starts

Ball Seat is the same as free bore.

Free Bore - the portion of the barrel from the end of the chamber to the beginning of the throat that is free from any rifling.

Bore diameter - the diameter of the bore at the top of the rifling lands.

Groove diameter - the diameter of the bore at the bottom of the rifling lands.

Leade - the area of the barrel from where the angle of the throat begins to where it reaches bore diameter.

Not saying this is 100% accurate, but it is how it was explained to me.

Attached Files

CB posted this 20 November 2007

This is certainly a better picture than I can make. I make the drawing in EXCEL, copy it to WORD, print it, photograph the print, put it into PHOTOSTUDIO, add the text andthen insert into a WORD document. Along the way I get lost several times, and I can't photograph the WORD print so it comes out looking white. There must be a better way.

I put the picture up on cast boolits in the middle of a thread about terminology, and the argument began.

I think it's time to put the words and meanings, and many words have several meanings, down into a simple paper.

From the end of the cartridge case place to the bore and groove place there are any number of things that can be cut into the ?chamber?.

How about we tell what the words mean to us? Remember, there's no right or wrong, if “XXXX” means “AAAA” to you, that's just what we want. Let's give the newcomer, and me, some help.

Here are some of the words:

Throat

Ball Seat

Leade

Free Bore

Bore Diameter

Groove Diameter

?????????

joe b.

  

Attached Files

CB posted this 20 November 2007

Hey Joe, see if this works for you. It as close I can gan git to scale. Its a .310” dia ball seat about .120” long with a 1.5 degree throat........Dan

Attached Files

CB posted this 20 November 2007

Hey Joe, that looks good, even in color.  I'll try one later and see what a scaled one looks like......................Dan

Attached Files

CB posted this 19 November 2007

Dan,

You're wrong but I give up.

Attached Files

CB posted this 19 November 2007

Here's the revised picture, I can't get my camera to take a white background picture.

??????

 

joe b.

Attached Files

CB posted this 19 November 2007

Joe,

You don't need to call it anything, but when you correct the drawing there will be a tapered ring between the straight cylindrical ball seat and the throat's tapered lands. In your example of a .310” ball seat and a .300 bore with a 1.5 degree throat .3820” in length, the lands will .3056” in length and the 'free-bore diameter' length will be .0764".

An interesting point is: with your example given the land height or groove depth is .004” with a 1.5 degree angle, the angled land length will always be .3056” as you increase or decrease ball seat diameter. The free-bore diameter length is the only length that changes past .308". A .311” diameter ball seat would have the free-bore diameter length of .1719".....................Dan

Attached Files

CB posted this 19 November 2007

I have to read this stuff a long time. Here's what I think. The drawing is wrong, it needs the additions Dan shows to show that the ball seat is .310” and the groove diameter is .308” for example. My drawing just has one line pair showing the ball seat dimension and labeled the groove bottom.

I'll try to fix the drawing.

I do not understand the free bore/ball seat business.

joe b.

Attached Files

CB posted this 14 November 2007

Well Pat, I think we said our part. This is a forum so lets see what others have to say.  I'm sure Joe's sketch is sufficient, but he's such a perfectionperfectpersonallanist......:D

Attached Files

CB posted this 14 November 2007

Dan,

You lost me on most of what you're saying and maybe you could try again but believe me the sketch, prints, and more than likely all the numbers, are right. The only thing I see that could be wrong is adding a comma behind the word “diameters” in the part you quoted and possibly (but stretching) Joe not putting the lines representing the groove lower but that's no big deal and this isn't an art or blueprint reading forum. When talking about throats for all practical purposes free bore and ball seat are the same thing.

There's no argument here, just talking.

Attached Files

CB posted this 14 November 2007

Wooooops, my mistake. I was talking about the 'free-bore diameter' pertaining to throat design, not the term concerning throat length associated to bullet jump. That is what Weatherby has, longer throats than the bullet AOL on a chambered cartridge. I've editied my other post to include the word diameter to free-bore.

The sketch is still wrong. I'm not talking about degrees or lengths, I'm talking about the sketch and Joe's dimension suggestion of a .310” diameter ball-seat, the ball-seat would be larger in diameter, not even with the grooves which would make the ball-seat .308” in diameter, even with the grooves. I don't know any chamber dimensions that have the ball-seat the same diameter as the groove diameter.

I'm not replying to argue, just replying to Joe's question if this is right and the sketch isn't.   Trying ta help ya out Joe.   :)

Attached Files

CB posted this 14 November 2007

Since I'm the one who got the ball rolling on this there isn't a mistake. If you look at the chart it says length for .001 reduction at the top so for a 310 x 45 min. throat the tapered section would be 10 x .077 or .770 long. For a .309 x 45 min throat it'd be 9 x .077 and so on. I use the 45 min, 1 degree, and 1 1/2 degree so know they're right, although rounded off, and assume Joe figured the rest right although he'll probably add something to this.

I hate to do this but I don't think the little angled part of the throat less rifling is called the free bore. Free bore and ball seat are just different names for the same thing unless I'm wrong here but I don't think I am. Weatherby uses about a 3/8 inch long straight section they call freebore to keep pressures down but in actuality it's just a long ball seat.

Attached Files

CB posted this 14 November 2007

Joe Brennan wrote: CHAMBER THROATS-THE INCLUDED ANGLE

            The “ball seat” is the cylindrical section of the throat. For a 30 caliber rifle with .300” bore and .308” groove diameters, the ball seat might be .310".  

Joe,

Your drawing in http://www.castbulletassoc.org/attachment.php?id=546>CHAMBER THROATS-THE INCLUDED ANGLE.doc is missing the 'free-bore' diameter area, with your example of a .300” bore, .308” groove with a might be .310” ball-seat. The ball-seat would be .002” over groove diameter. That .002” angled part of the throat between the cylindrical ball-seat and the angled groove and lands is called the 'free-bore' diameter. Thus, the greater the diameter of the ball-seat over groove diameter, the greater of area the free-bore diameter. The red lines here in http://www.castbulletassoc.org/attachment.php?id=546>CHAMBER THROATS-THE INCLUDED ANGLE.doc II is where the bottom of the groove ought to be.  The two arrows point to the free-bore diameter section.  Good example tho Joe...........................Dan

Attached Files

CB posted this 18 August 2007

Joe,

The numbers are degrees and minutes. 1 degree 22 minutes and so on. The 1 degree 22 min. is the throat angle, 2deg 44 min. incl. No lead (ball seat). The 30-30 is 30 deg. incl. right from the end of the chamber neck.

Especially with the 30-30, but in all cases, I think you can see why I said before in another thread that the case neck has to be considered part of the throat

Pat

Attached Files

CB posted this 18 August 2007

Pat;

35-44 degrees, is it 35.44 degrees or 35 degrees 44 min.? 1-22 degrees, is it 1.22 or 1 degree 22 min? Is the 1-22 angle the throat?

Thanks;

joe brennan 

Attached Files

CB posted this 17 August 2007

The other.

Attached Files

CB posted this 17 August 2007

Here Joe. The only other one I know of is the Weatherby which is just a long lead (ball seat) like a cast bullet throat.

Pat

Attached Files

Show More Posts
Categories
Search
Popular Tags
This Weeks High Earners
Hot Topics
Close