Cylinder size maters

  • 2.7K Views
  • Last Post 07 April 2016
rmrix posted this 10 March 2016

Any of you that know something about revolver accuracy please chime in. Being mostly a rifleman, I know next to nothing. Short story coming...

I am going to try my hand at 100 meter silhouette matches with a Ruger 44 Super Blackhawk. I shoot the local monthly lever rifle  matches as time allows and there is a small bunch of people that enter twice, once in pistol caliber Lever rifle class and just for kicks shoot the same course with a single action revolver - local match restriction on firearms to keep the event from turning into unlimited. So just SA revolver is competing.

  So.... I have a 1970's era Super BH that I plinked the daylights out of when I was young and foolish. PLEASE! No need to tell me I am still foolish. Tho it may be true.

 - OK. I have gun - I'm good to go.

On a whim, I cleaned and pin-gauged the cylinders on my old friend.  After all, accuracy counts. Maybe I'll learn something.  BTW- I envision I will be shooting a light load -maybe like  5-6 grains of Universal or Unique pushing a 250 grain SWC.

Getting back to the subject, the cylinder; The holes are big on the exit side of the cylinders! The good news, at least they all felt very close to the same size!

I worked my way up through the pins to 0.432” GO, 0.433” NO GO.

So, .......... What would you think about shooting my largest diameter bullet? It  is out of round 0.429"-0.430"? OR? Do I need to buy a larger bullet mould?

Learning that the cylinders are as large as they are got me going!  So. I got out my few other 44's. The Uberti Model P blackpowder 44 Special cylinder was smaller -   0.430” GO  -  0.431” NO GO   all cylinders Hmmmm, OK

My last 44, a Smith Model 696 44 Special goes smaller yet! all cylinders - 0.428” GO -  0.429” NO GO.

I'm not sure where my question is exactly but at the least, is that a size difference that is too large to be covered by the same bullet sized the to the same diameter? And for best accuracy would I want a larger bullet the Ruger?

Attached Files

Order By: Standard | Newest | Votes
Brodie posted this 11 March 2016

rmix, Either get a new mold or send that one to Eric at http://www.hollowpointmold.com/and have him open up the driving bands to. 431 or .432, and maybe size those bullets down when you are going to load for the Smith.  The other option is to buy an Accurate Arms mould and specify the size you want, using your present mould for the Smith where the bullets can be squozen to size as they pass through the smaller cylinder openings.

Over-sized cylinder throats and the bullets just bounce around them any old way and enter the barrel the same way ruining accuracy. 

Smaller than barrel cylinder throats are a real mess.  The smaller than bore bullets enter the barrel and skid leading like crazy and often tumbling before they hit the target.  Like my old Charter Arms Bulldog.  One out of every five rounds fired at 25 yd. hit the target sideways, because when the barrel was swagged into the frame they over did it and made a small spot in the bore.  Brodie

B.E.Brickey

Attached Files

R. Dupraz posted this 11 March 2016

Yep,pretty much covers it! If you use that 0.429'-0.430” bullet in that Blackhawk you definitely will not be happy with the results.

Attached Files

rmrix posted this 11 March 2016

Old Coot wrote: rmix, Either get a new mold or send that one to Eric at http://www.hollowpointmold.com/and>http://www.hollowpointmold.com/and have him open up the driving bands to. 431 or .432, and maybe size those bullets down when you are going to load for the Smith.  Brodie OK, Right but going a little deeper into the subject.

A 0.431” bullet diameter will fall through and a 0.432” will pass through the throats with out touching. Our old rule is a 0.001” over (or more) so if this is followed a 0.433” + is needed to seal and not rattle around.

I have no doubt the small 0.430” SWC will not work best, however it has shot reasonably well with heavy loads.  Maybe the bullets were getting a little bump up in diameter.

I have not slugged the barrel yet. Maybe later.  Assuming the barrel is not 0.433” diameter, I don't think the cylinder/barrel is all that great a match.

Attached Files

gnoahhh posted this 11 March 2016

And here I thought the subject was about really small garden veggies!:D

Attached Files

JSH posted this 11 March 2016

If the 430 is as big as your mold cast “beagle” it with some aluminum tape. I don't know how recoil sensitive you are but 2400 is my silhouette powder in the 44. I highly suggest you get sight settings for each distance. Then change settings as needed. Yes you can use Kentucky elevation, but be warned changing lite and shadows will cause you grief.  

Attached Files

rmrix posted this 11 March 2016

JSH - thanks for the good suggestion. There is no right or wrong on this. I would say, I would not put tape on the mold. I can however open the bands a little or easier yet, get a larger mold.

2400 powder- yup. Shot it a lot in the 1970's The bigger the boom the better! Right:D I will find and accurate load (and bullet) and get sight settings for it.  I am an old match shooter. Sight settings are the way to go. I am more interested in a light load. These 100 meter targets go down - a 200-250 grain bullet at almost any velocity will take them down. I just need to have accuracy and skill.

Thanks for the good input!

Attached Files

RicinYakima posted this 11 March 2016

Michael,

I have been pretty successful with just using softer alloy with lighter loads, as in 1/2 WW's and 1/2 pig lead. Normally I have used SR7625 or WW231. The other alternative, as least for me, is to use a hollow based bullet. That is rare for a .44, other than Keith's #429422. Just a couple of thoughts to help you get confused.

Ric

Attached Files

JSH posted this 11 March 2016

The tape thing was just a thought to see if the larger bullet in that design shoots better. The stickum will come right off with some acetone. We had fair luck with the Lee tumble lube 180-44 RN and Bens liquid lube. As cast 50/50. This was used on the IHMSA field pistol/NRA hunter size targets. The key is always accuracy of course. Get around 18-20 of the closest targets and scratch out what you can on the further ones, I try for 50%. That will give you a score of mid to high 20's or mid to low 30's, usually good to finish in the top of the pack. Don't forget the main thing, have fun! Jeff

Attached Files

Pigslayer posted this 11 March 2016

gnoahhh wrote: And here I thought the subject was about really small garden veggies!:D
Heh-Heh.  

If someone else had of done to me what I did to myself . . . I'd have killed him. Humility is an asset. Heh - heh.

Attached Files

Tom Acheson posted this 11 March 2016

Just a look back some history with the Ruger SBH as used in handgun silhouette matches. In the late 70's and early 80's the most popular revolver for use in the IHMSA Revolver category was the Ruger SBH in .44 Mag. Most shooters used jacketed bullets and WW 296 or H-110 powder. For the few of us that used CB's, the conclusion was that the the CB had to be sized at 0.432”. The favorite rumor at the time was that the lawyers (I bet Ed Harris has a comment here) at Ruger were nervous about hand-loaders so the inside barrel dimensions were supposedly made on the “generous” side. I can't recall anyone getting into the cylinder throat dimensions in that era that we see so prevalent today. The oversize bore was there for jacketed and CB shooters. Maybe that is why perfect scores of 40x40 were infrequent until the Freedom Arms revolvers appeared on the scene?     Tom

Attached Files

Brodie posted this 11 March 2016

rmrix, Sorry I misspoke when I typed in the size to have Eric open your mould to.  I was pretty tired and sleepy.  But, you were able to figure it out any way. B

B.E.Brickey

Attached Files

Ed Harris posted this 11 March 2016

You might also try 7 grains of Bullseye and see if the bullets slug up more uniformly with the alloy you are using. I've had good luck with it. WST is another good choice if you can find any.

In the .44 Magnum I've had good luck at long range, 100 yards revolver, 200 yards rifle, using Accurate 43-230EB which is a modified John Kort design intended for the .44-40 using black powder.  Its traditional nose shape carries up very well at long rifle range and the longer shank length also takes up some of the excess free airspace in the case when using light charges of fast-burning powders. 

I use 7.2 grains of Bullseye in both my .44-40 and .44 Magnum Rugers and cast with 1:30 tin/lead from Roto Metals.

Good hunting bullet too!

73 de KE4SKY In Home Mix We Trust From the Home of Ed's Red in "Almost Heaven" West Virginia

Attached Files

Tom Acheson posted this 11 March 2016

Odd....in my S&W Model 57 .41 Mag. I found that 7.0 of Bullseye worked well with a H&G Keith Type plain base 220-grain bullet.

Tom

Attached Files

rmrix posted this 13 March 2016

Ric, Yes, I think I will try going very soft to see what happens.

Attached Files

rmrix posted this 13 March 2016

Old Coot wrote: rmrix, Sorry I misspoke when I typed in the size to have Eric open your mould to.  I was pretty tired and sleepy.  But, you were able to figure it out any way. B

Not a problem - I was on top of the size thing.

I may try to open up one of my molds. I would try that on a LEE mold first but got rid of them all except for a fulll WC 44 bullet. Not too interested in a full WC for 100yd shooting  .>.

Attached Files

rmrix posted this 13 March 2016

Ed Harris wrote: You might also try 7 grains of Bullseye and see if the bullets slug up more uniformly with the alloy you are using. I've had good luck with it. WST is another good choice if you can find any. I use 7.2 grains of Bullseye in both my .44-40 and .44 Magnum Rugers and cast with 1:30 tin/lead from Roto Metals. Good idea, I can try that too.  I dug around my lead pile and found some very soft Pb-Sn on the order of 40-1.

I have Bullseye and HP-38 and very little clays.  I will give it a try. Might be just the answer.

That bullet Print looks like a very good design to have made in custom band size. Being cheap, I may have to exhaust all available resources. Then, do the correct thing and buy a good mold. 

Attached Files

rmrix posted this 30 March 2016

I got a chance to shoot this 44 Revolver with the large .432” cylinder today. Not much accuracy to really get excited about. My soft RCBS 250 KT bullets shot 3” 25 meters groups and about double that for 50 meters.

I set out steel swingers at the correct ranges in order to get rough sight settings by going to zero or all the way down on the rear sight and counting clicks back up. This was made easy because I was at the 100 meter silhouette range where we hold the pistol caliber lever rifle matches.

I also set up paper targets at 25, 50 and 100 meters to check for group. And, in case anybody is wondering, I did not shoot enough of any one load to make any kind of statistical dent in real data.

The size of main part of the 100meter steel silhouettes targets are Chicken-3” , Pig-4.5", Turkey-5” and Ram - 6+ inches, all measured belly to back. So targets are about 6 moa vertical.

Clearly, my smokeless loads need some help but on a whim I had loaded ten black powder rounds with the same bullet and fired all of them into the 25y paper target.

I fired them in two five shot groups on the same bull. I guess I took a break after five to ponder the nice little knot of holes. The first five were incredibly tight printing at 9:00 and the second group had vertical and additional windage flyers. BUT, the 10 shots together cut any and all the smokeless load groups by half!

Hmmmm, shooting an undersized, soft bullet with blackpowder; it might not be the answer but in this case I say it is worth looking into until I can lap out the bands on the mold.

Attached Files

RicinYakima posted this 30 March 2016

That is exactly the way they did it in the 1800's! Soft bullets, black powder and obduration. It still works but most don't like the mess of cleaning every other cylinder full.

Attached Files

rmrix posted this 30 March 2016

RicinYakima wrote: It still works but most don't like the mess of cleaning every other cylinder full.I'm am not sure I can keep the revolver running smooth over the 40 shot coarse. I can keep the cylinder turning if that is all but I bet there will be more to it.

I've put more than 50 ea at a time through my 45 Colt and 44 Special with BP but it was close range can shooting. Plus, I don't remember the down side because I was having fun and we only remember the fun parts!    That may be the limiting factor in spite of it being fun and having a pleasant base drum boom.

In addition to lock up, accuracy may drop off too.   Not sure. I've only fired these ten at paper and from rest.

Likely, if I can get good accuracy with this revolver out the the undersized bullet and BP, I can get accuracy from a correct sized bullet and smokeless.   That may be the better choice for match shooting.

But, I'm pretty sure I will practice run through the course of fire (40) with the BP just for the fun of it and see what happens.

Attached Files

gunarea posted this 30 March 2016

Hey rmrix      2004, 2005 NRA Hunters Pistol Big Bore Iron sight division, Florida Sunshine State Shooting Competition. Back to back gold medals, running home cast projectiles through my old SBH three screw. RicinYakima hit it on the nose, soft cast. For proper obturation, a fast pressure spike propellant is needed. Distance specific ammunition was my choice of options. Three different cast projectiles were used to eliminate sight changes. All loadings were sub-sonic, and marked with a Sharpie for easy identification.      2004 won using Alliant Red Dot, 2005 won using Alliant Promo. All cast projectiles from Lyman moulds in 215gr SW, 245gr SW and 315gr SW. The big bullet needs a heavy crimp to avoid dislodging neighbors under fire.      Just an amusing anecdote, after knocking feet off of two different Ram targets, complaint of over powered ammunition brought forth judges to examine everything I had with me. Upon finding nothing but cast bullets, it was determined the welds must have been at fault. My Ram load is 6.1gr Red dot/Promo pushing the 315gr Keith type SW. Good horn hits spun the target wildly while other good hits knocked Rams back 25 feet.      I would provide my winning load combination to any whom would like the data. Working the loads to gold medal level was by far the most rewarding for me. There is one more secret weapon which I provide to those who compete in Big Bore Iron Sights against me. Let me know when you are ready. Best of skill to you.                                                  Roy       

Shoot often, Shoot well

Attached Files

Show More Posts
Categories
Search
Popular Tags
This Weeks High Earners
Hot Topics
Close