To remover powder coating???

  • 488 Views
  • Last Post 26 July 2022
  • Topic Is Solved
2frogs posted this 22 May 2022

I was given some powder coated 44 bullets I want to melt down to cast 38/357 bullets. What's the best way to remove the powder??

Attached Files

Order By: Standard | Newest | Votes
Little Debbie posted this 22 May 2022

Shooting them would be the easiest solution. If that won’t do it melt them in a pot you don’t care about outside and away from neighbors. Stay up wind and prepare to be unhappy with the mess. You will be able to scoop the black goo off the top and then flux to clean further. My experience was with maybe 30 or 40 9mm powder coated bullets in my 50 pound pot I use to melt, blend , and clean scrap alloy. It was a smoking dirty episode that was not worth my time.

Attached Files

  • Liked by
  • Jack47
  • RicinYakima
2frogs posted this 23 May 2022

You get very little selling. Better to melt down.

Attached Files

  • Liked by
  • Jack47
  • Fitzpatrick
Fitzpatrick posted this 23 May 2022

I have melted a bunch of them down and no more smoke than fluxing , leave black goo in pot and it will turn to ash, also scoop same as you would dross and continue casting.

Attached Files

  • Liked by
  • max503
  • Buttersdad
pisco posted this 28 May 2022

I just throw them in the melting pot 

Attached Files

  • Liked by
  • max503
  • 2frogs
delmarskid posted this 23 May 2022

Roll them in paint remover maybe? Then hit them with a hose real hard when they are good and blistered. That might get a bunch off before you try and melt them . I’m assuming you know enough to let them get bone dry first.

Attached Files

  • Liked by
  • 2frogs
Little Debbie posted this 23 May 2022

I’ve found that melting is the only way to remove cured powder coat. Acetone, mineral spirits, and lacquer thinner seem to have no effect on powder coat……should have been a little clearer about the reason for re-melting powder coated bullets to reclaim lead.

Attached Files

  • Liked by
  • Jack47
Buttersdad posted this 27 May 2022

When I first started casting I made my own alloy, needless to say it wasn't a good batch. I also started powder coating at the same time. When I baked my pills 99% of them melted to puddles. I put them back in the melting pot the next time I melted a batch and like said above there was a bit of smoke but not too much. I used a couple big handfuls of sawdust through the session to get the goo out. Then fluxed as usual and it all came out good. That was years ago and I would do it the same today. BTW, I always do my melting and casting outside.

Attached Files

  • Liked by
  • 2frogs
Ken Campbell Iowa posted this 27 May 2022

be really cautious about the smoke ... you will kill every canary in the neighborhood ....

Attached Files

  • Liked by
  • 2frogs
2frogs posted this 22 May 2022

I don't have a 44 any more. I will get a pan from our local flea shop and see how it goes. Hate to trash them,must be close to hundred or so. Be good alloy for my 38/357.

Attached Files

RicinYakima posted this 23 May 2022

Sell to the recyclers and you will be time and money ahead.

Attached Files

Clod Hopper posted this 23 May 2022

Where are you 2frogs?  A local gun store might give you something for them or find a .44 shooter/reloader.

Dale M. Lock

Attached Files

Duane Mellenbruch posted this 23 May 2022

If you melt the bullets in a scrap melting pot, add plenty of saw dust to give the goo something to attract instead the sides of the pot.  About like melting down roof flashing with tar.  It will smoke so the saw dust will burn and help with the smoke generated.  Like you I hate to waste good cast bullets, but there are times that is the best solution.

Attached Files

2frogs posted this 23 May 2022

Yeah bone dry

Attached Files

Boschloper posted this 24 May 2022

Melt them outside and let them smoke. The sawdust is a good idea. 

Attached Files

Barn-Dweller posted this 26 July 2022

I was given some powder coated 44 bullets I want to melt down to cast 38/357 bullets. What's the best way to remove the powder??
I just throw them in the pot when I am starting a new casting session. I never put more than about 20% in the pot. They smoke a little then the powder coat just burns up and is on the surface and I skim it off. I always have a reject jar with some alone with the rejects when I look at my bullets after casting before powder coating. It all just goes back in the pot. 

 

Attached Files

Close