I have a 30-30 in a contender and it has just about no freebore is this a job I can do with hand tools and a reammer,or do I need to send it of to a gunsmith
adding freebore or throat to a 30-30 contender
- 638 Views
- Last Post 12 July 2022
- Topic Is Solved
That is white Label Lube , Liquid Alox with powder Graphite added it make a water resistant paper patch and good lube.
Attached Files
Excellent work.
Now all I need to know is the mysterious lube you are using
Attached Files
Here is a picture of the little rifle. Contender 23" barrel 30/30 cal.
Attached Files
I think we have success! My first five shots was with a 230 gr bullet, paper patched over 18 gr of reloader 7.
The second five shots was a 200 gr bullet paper patched over 18 gr of reloader 7.
Both five shot groups at the same target at fifty yards.
Attached Files
Next task is to head to the range will post the results .
Attached Files
here are some pictures of the added freebore to the 30-30 , and a dummy round to check for fit , so far fits like a glove. Thanks for helping me make this happen Ken Campbell.
Attached Files
Glen you 100% right , I form my brass from the 38-55 long and trim back to 2.125 that gets me .005 off the chamber wall and with cast loads seems the brass doesn't grow after that.
Attached Files
That looks like your typical 30-30 chamber - no throat. A .310" x 3° throating reamer will do wonders. Careful measurement may also show that the chamber is considerably longer than your cases. Reforming 38-55 brass helps with that.
Glenn
Attached Files
Here is the a casting of the chamber that I am going to enlarge the throat of.
Attached Files
The base diameter is about 0.410-0.411 and the Patch to bore body is about 0.400
that is with Seth Cole 55W paper.
PM me your full name and address and I will send you a few.
beltfed/arnie
Attached Files
Very nice , I might Have to talk you out of a few of those to try in my CPA 40-65 it also has a 1/16 twist and a 34 in Douglas barrel,
what's the diameter of bullet after patching ?
Attached Files
Fitzpatrick,
Here is a pic of the DDEPP bullet for 16 twist 40 cal, Shot at 100yds
with my rebuilt 40-65 Hi Wall/16 twist K&P barrel.
My first DDEPP design.
Look up Buffalo Arms JIM# 403380E.
beltfed/arnie
Attached Files
Yea , I also heard that if I just put some valve grinding compound on a bullet, tap the end with threads install a bolt and use a cordless drill that I could increase the throat, But I think I will try a throater first and see how that works.
In my Savage model 340 and with the reliable Winchester model 94 I have good groups with bullet up to 200 gr. but with the COL length limit and the 1/12 twist that seems to be my wall. With the Contender I'll have no limit on COL and the 1/10 twist should do well with the heavies.
Attached Files
Thank’s Fitzpatrick
I’m inspired to get my stuff out and have another go.
I have been sleeping and having fun with mild pb bullets for the last few years.
If you rub some grit on non lubed patched bullets you throat will get longer quickly enough.( attempt at humour)
Attached Files
these are a couple of choices I am working on, both are 230 gr.
Attached Files
Yes it works with smokeless real well , I'm heading off to work for now but when I get home this afternoon I will post some pics of the bullets
Attached Files
Would like to see the cast bullet and a wrapped one of those.
So DD pp’ed bullets work for smokeless then?
Attached Files
Categories
- All Categories
- General Polls
- Contact Us w/ Forum Issues
- Welcome to The Cast Bullet Association Forum
- General
- Bullet Casting
-
Guns and Shooting
- AR Platform
- TC Contenders & Other Single Shot Handguns
- Shotguns
- Informal Matches & Other Shooting Events
- Gunsmithing Tips
- Gun Cleaning & Maintenance
- Optics
- Benchrest Cast Bullet Shooting
- Military Bench Rest Cast Bullet Shooting
- Silhouette Shooting
- Postal Match Cast Bullet Shooting
- Factory Guns
- Black Powder Cartridge
- Hand Guns
- Lever Guns
- Single Shot Rifles
- Bolt Action Rifles
- Military Surplus Rifles
- Plinkers Hollow
- Muzzleloaders
- Hunting
- Reloading
- Buy, Sell or Trade
- Other Information & Reference
Search
This Weeks High Earners
- jeff houck 20
- Wilderness 14
- Tom Acheson 14
- Aaron 13
- John Carlson 13
- sghart3578 10
- Spindrift 5
- alphabrass 5
- SkinnerD 5
- MP1886 3